Ibase FWA8208 Instrukcja Użytkownika

0 FWA8208 Series Networking Appliance Users Manual Version: 1.1

9 Connector Locations on MB967

10 CN1: USB 3.0 Box Header CN2: COM1 RJ45 Connector Pin # Signal Name (RS-232) 1 RTS, Request to send 2 DTR, Data terminal ready 3 TXD, Tra

11 J4: COM2 Serial Port Pin # Signal Name (RS-232) 1 DCD, Data carrier detect 2 RXD, Receive data 3 TXD, Transmit data 4 DTR, Data te

12 J20, J21: USB 2.0 Pin Header FAN1, 2, 3: System Fan Power Connector FAN1/2/3 are 4-pin headers for System fan power. Pin # Signal Name 1 Ground

13 Front Panel Features Rear Panel Features FWA8208 & FWA8208-2SLOT FWA8208-RPSU 3x Smart Fans One or two Add-on Card Expans

14 Chapter 4 Console Mode Information FWA8208 supports output information via Console in BIOS level. Prepare a computer as client loaded with an e

15 4. Please make the port settings to Baud rate 19200, Parity None, Data bits 8, Stop bits 1 5. Power on FWA8208. Press <Tab> key to enter

16 Chapter 5 Open the Chassis Fig. 5-2 Take off six screws and open the top lead Fig. 5-3 The base stand Chapter 6 Installing DDR3 Memory In

17 Chapter 7 Installing CompactFlash Card Insert CompactFlash card into the socket. Fig. 7-1 Insert CompactFlash Card into the CF interface Fig.

18 Chapter 9 Installing 2.5” HDD (FWA8208 & FWA8208-RPSU) Fig. 9- Take off two screws on bottom to remove 2.5” HDD bracket. Fig. 9-2 Fasten

1 Table of Contents Chapter 1 Introduction 3 Chapter 2 System Specification ...

19 Chapter 10 Installing Optional Dual 2.5” HDD Kit The following is for optional Dual 2.5” HDD kit: Fig. 10-1 Push eight shock-absorbent pads

20 Chapter 11 Installing Add-on Card Fig. 11-1 Loosen screw on slot bracket. Fig. 11-2 Slide in PCI-e add-on card. Fig. 11-3 Fix the add-on car

21 Chapter 13 BIOS Information This setup allows you to view processor configuration used in your computer system and set the system time and date.

22 Above 4G Decoding Enables or Disables 64bit capable devices to be decoded in above 4G address space (only if system supports 64 bit PCI decoding).

23 Unpopulated Links In order to save power, software will disable unpopulated PCI Express links, if this option set to ‘Disable Link’. ACPI Setting

24 CPU Configuration This section shows the CPU configuration parameters. Aptio Setup Utility Main Advanced Chipset Boot Security Save

25 SATA Mode Selection (1) IDE Mode. (2) AHCI Mode. (3) RAID Mode. Shutdown Temperature Configuration Aptio Setup Utility Main Advanced Ch

26 Acoustic Management Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Acoustic Management Confi

27 F81866 Super IO Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Super IO Configuration → ←

28 Console Redirection Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit COM0 Emulation: ANSI: Extended

2 Foreword To prevent damage to the system board, please handle it with care and follow the measures below, which are generally suffici

29 Wake on LAN Enable or disable integrated LAN to wake the system. (The Wake On LAN cannot be disabled if ME is on at Sx state.) SLP_S4 Assertion

30 System Agent (SA) Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit System Agent Bridge

31 Boot Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Boot Configuration → ← Select Scre

32 Launch PXE OpROM policy Controls the execution of UEFI and Legacy PXE OpROM. Launch Storatge OpROM policy Controls the execution of UEFI and Lega

33 Save Changes Save Changes done so far to any of the setup options. Discard Changes Discard Changes done so far to any of the setup options. Rest

34 { printf(" Parameter incorrect!!\n"); return (1); } bTime = strtol (argv[1], endptr, 10); printf("System will

35 //--------------------------------------------------------------------------- #include "F81866.H" #include <dos.h> //-------------

36 return Result; } //--------------------------------------------------------------------------- //-----------------------------------------------

37 Chapter 15 Digital I/O Sample Configuration Filename：Main.cpp //--------------------------------------------------------------------------- //

38 Dio5SetOutput(0x00); //clear // DIO = Dio5GetInput() & 0x0F; Dio5SetOutput(0x00); //clear DIO = Dio5GetInput() & 0x0F;

3 Chapter 1 Introduction FWA8208 series was specifically designed for the network security & management market. Network Security Applications:

39 ucBuf = Get_F81865_Reg(0x30); ucBuf |= 0x01; Set_F81865_Reg(0x30, ucBuf); Set_F81865_Reg(0xA0, 0x00); //define as input mode

40 ucDid = Get_F81865_Reg(0x20); if (ucDid == 0x07||ucDid == 0x10) //Fintek 81865/66 { goto Init_Finish; } F81865_BASE = 0x2E;

41 #ifndef __F81865_H #define __F81865_H 1 //--------------------------------------------------------------------------- #define F81865_INDEX_

42 Chapter 16 Drivers Installation This section describes the installation procedures for software and drivers under the Windows. The software and

43 3. When the Welcome screen to the Intel® Chipset Device Software appears, click Next to continue. 4. Click Yes to accept the software lice

44 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. VGA Drivers Installation NOTE: Bef

45 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to to agree with the license agreement and continue the installation

46 6. On Setup Progress screen, click Next to continue. 7. Setup complete. Click Finish to restart the computer and for changes to take effect.

47 3. Click Install Drivers and Software. 4. When the Welcome screen appears, click Next. 5. Click Next to to agree with the license agreement.

48 6. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue. 7. The wizard is ready to begin installa

4 Chapter 2 System Specification Product Name FWA8208 Form Factor 19” 1U Mainstream Networking Product Motherboard MB967 CPU Intel® LGA1155 Series

49 Intel® Management Engine Interface Follow the steps below to install the Intel Management Engine. 1. Insert the CD that comes with the

50 3. Click Yes to to agree with the license agreement. 4. When the Setup Progress screen appears, click Next. Then, click Finish when the setu

51 Intel® USB 3.0 Drivers 1. Insert the CD that comes with the board. Click Intel and then Intel(R) C216 Series Chipset Drivers. 2. Click Intel(

52 4. Click Yes to to agree with the license agreement and continue the installation. 5. On the Readme File Information screen, click Next to conti

53 Appendix-A I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of t

54 Appendix-C FWA8208 Series Configurations The following lists the available SKUs of FWA8208 for different system requirement. FWA8208 2.5”

5 Operation Humidity 5% ~ 95% Certifications CE, FCC Compatible Front Expansion Cards  IBP161: 4-port RJ-45 10/100/1000 Copper LAN Module Card 

6 Chapter 3 Hardware Configuration Jumper Locations on MB967

7 Jumper Settings on MB967 JP6, JP5, JP4: Bypass LANs & Reboot Setting JP2: Clear CMOS Contents Use JP2 to clear the CMOS contents.

8 JP9: ATX & AT Mode Select JP9 Setting Function Short/Closed AT Mode (Default) Open ATX Mode J17: PCIE1 & PCIE2 Golden Finger PCI-e Con