Ibase IB827 Instrukcja Użytkownika

IB827 Intel® Atom 945GSE PICMG 1.0 CPU CARD USER’S MANUAL Version 1.0

INSTALLATIONS 6 IB827 User’s Manual Installations This section provides information on how to use the jumpers and connectors on the IB827 in order to

INSTALLATIONS IB827 User’s Manual 7 Installing the Memory The IB827 board supports two DDR2 memory sockets to support up t

INSTALLATIONS 8 IB827 User’s Manual Setting the Jumpers Jumpers are used on IB827 to select various settings and features according to your needs an

INSTALLATIONS Jumper Locations on IB827 IB827 User’s Manual 9

INSTALLATIONS JP1: ATX or AT Power Selection JP1 ATX Power ATX AT JP3: LCD Panel Power Selection JP3 LCD Panel Power 3.3V 5V JP10: CompactFl

INSTALLATIONS JP2, JP4, JP5: RS232/422/485 (COM2) Selection COM1 is fixed for RS-232 use only. COM2 is selectable for RS232, RS-422 and RS-485.The fo

INSTALLATIONS JP6: COM2 RS232 +5V/+12V Power Setting JP6 Setting Function Pin 1-2 Short/Closed+12V Pin 3-4 Short/ClosedNormal Pin 5-6 Short/Clos

INSTALLATIONS JP12: USB0, USB1 (CN1, J24) Power Setting JP12 Setting Function Pin 1-2 Short/Closed+5VSB Pin 2-3 Short/Closed +5V JP13: USB2, USB

INSTALLATIONS 14 IB827 User’s Manual This page is intentionally left blank.

INSTALLATIONS IB827 User’s Manual 15 Connectors on IB827 J9: IDE Connector ...

ii IB827 User’s Manual Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International

INSTALLATIONS J9: IDE Connector Signal Name Pin # Pin # Signal NameReset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5

INSTALLATIONS FDC: Floppy Drive Connector Signal Name Pin # Pin # Signal Name Ground 1 2 RM/LC Ground 3 4 No connect Ground 5 6 No connect Ground

INSTALLATIONS VGA: VGA Connector (D-sub, 15-pin) Signal Name Pin # Pin # Signal NameRed 1 2 Green Blue 3 4 N.C. GND 5 6 GND GND 7 8 GND VCC 9 10

INSTALLATIONS J5: System Function Connector J5 provides connectors for system indicators that provide light indication of the computer activities and

INSTALLATIONS Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then

INSTALLATIONS J6: ATX- Power Signal Connector Pin # Signal Name 1 Ground 2 PS-ON 3 5VSB J10: SPI Flash Connector (factory use only) J11, J12: S

INSTALLATIONS J19: USB6/7 Ports 15 Signal Name Pin Pin Signal NameVcc 1 5 Ground D7- 2 6 D6+ D7+ 3 7 D6- Ground 4 8 Vcc J23: PS/2 Keyboard/Mouse

BIOS SETUP IB827 User’s Manual 23 BIOS Setup This chapter describes the different settings available in the Award BIOS that

BIOS SETUP 24 IB827 User’s Manual BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel

BIOS SETUP IB827 User’s Manual 25 Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency/Voltage Control

IB827 User’s Manual iii Table of Contents Introduction ... 1 Pro

BIOS SETUP 26 IB827 User’s Manual Standard CMOS Features “Standard CMOS Features” choice allows you to record some basic hardware configurations in y

BIOS SETUP IB827 User’s Manual 27 To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to s

BIOS SETUP 28 IB827 User’s Manual Video This field selects the type of video display card installed in your system. You can choose the following vide

BIOS SETUP IB827 User’s Manual 29 Advanced BIOS Features This section allows you to configure and improve your system and a

BIOS SETUP 30 IB827 User’s Manual Hyper-Threading Technology By default, this field is enabled. Quick Power On Self Test When enabled, this field s

BIOS SETUP IB827 User’s Manual 31 Typematic Rate (Chars/Sec) When the typematic rate is enabled, the system registers repe

BIOS SETUP 32 IB827 User’s Manual Advanced Chipset Features This Setup menu controls the configuration of the chipset. Phoenix - AwardBIOS CMOS Setu

BIOS SETUP IB827 User’s Manual 33 Precharge Delay (tRAS) The default setting for the Precharge Delay is Auto. System Memor

BIOS SETUP 34 IB827 User’s Manual SDVO Panel Number This field allows you to select the SDVO Panel type. The default values for these ports are:

BIOS SETUP IB827 User’s Manual 35 Integrated Peripherals This section sets configurations for your hard disk and

iv IB827 User’s Manual This page is intentionally left blank.

BIOS SETUP 36 IB827 User’s Manual Phoenix - AwardBIOS CMOS Setup Utility SuperIO Device POWER ON Function BUTTON ONLY ITEM HELP KB Power ON Passwo

BIOS SETUP IB827 User’s Manual 37 IDE Primary/Secondary Master/Slave UDMA These fields allow your system to improve disk I/O

BIOS SETUP 38 IB827 User’s Manual Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the motherboar

BIOS SETUP IB827 User’s Manual 39 Power Management Setup Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup Po

BIOS SETUP 40 IB827 User’s Manual Power Management This field allows you to select the type of power saving management modes. There are four selectio

BIOS SETUP IB827 User’s Manual 41 CPU THRM-Throttling By default, this field is set to 50%. Wake up by PCI Card By defaul

BIOS SETUP 42 IB827 User’s Manual PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus

BIOS SETUP IB827 User’s Manual 43 PC Health Status This section shows the parameters in determining the PC Health Status.

BIOS SETUP 44 IB827 User’s Manual Frequency/Voltage Control This section shows the user how to configure the processor frequency. Phoenix - AwardB

BIOS SETUP IB827 User’s Manual 45 Load Fail-Safe Defaults This option allows you to load the troubleshooting default values

INTRODUCTION IB827 User’s Manual 1 Introduction Product Description The IB827 is a PICMG 1.0 full-size single board comput

BIOS SETUP 46 IB827 User’s Manual This page is intentionally left blank.

DRIVERS INSTALLATION IB827 User’s Manual 47 Drivers Installation This section describes the installation procedures for sof

DRIVER INSTALLATION Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before the software drivers to e

DRIVERS INSTALLATION VGA Drivers Installation To install the VGA drivers, follow the steps below to proceed with the installation. 1. Insert the

DRIVER INSTALLATION Realtek High Definition Audio Driver Installation Follow the steps below to install the Realtek High Definition Audio Drivers.

DRIVERS INSTALLATION LAN Drivers Installation Follow the steps below to install Realtek 8111C LAN drivers. 1. Insert the CD that comes with the

APPENDIX 52 IB827 User’s Manual Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which

APPENDIX IB827 User’s Manual 53 B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify

APPENDIX 54 IB827 User’s Manual C. Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable co

APPENDIX IB827 User’s Manual 55 void copyright(void) { printf("\n======== Winbond 83627EHF Watch Timer Tester (AUTO

INTRODUCTION Checklist Your IB827 package should include the items listed below. • The IB827 CPU card • This User’s Manual • 1 CD containing

APPENDIX 56 IB827 User’s Manual //=========================================================================== //

APPENDIX IB827 User’s Manual 57 //=========================================================================== void Set_W627

APPENDIX 58 IB827 User’s Manual D. Digital I/O Sample Code Filename: W627hf.h //====================================================================

APPENDIX IB827 User’s Manual 59 Filename: W627hf.cpp //====================================================================

APPENDIX 60 IB827 User’s Manual W627HF_BASE = 0x00; result = 0; Init_Finish: return (result); } //============================================

APPENDIX IB827 User’s Manual 61 File of the Main.cpp //====================================================================

APPENDIX 62 IB827 User’s Manual unsigned char result; Set_W627HF_LD(0x07); //switch to logic device 7 Set_W627HF_Reg(0xF0, Mask); //se

INTRODUCTION IB827 User’s Manual 3 IB827 Specifications Product Name IB827 Form Factor Full Size CPU Card (PICMG 1.0) C

INTRODUCTION [ Board Dimensions 4 IB827 User’s Manual

INTRODUCTION IB827 User’s Manual 5