Ibase IB897 Instrukcja Użytkownika

IB897 Intel® AtomTM E3800 SoC Series 3.5” Disk Size SBC USER’S MANUAL Version 1.0

INSTALLATIONS 6 IB897 User’s Manual Installing the Memory The IB897 board supports TWO DDR3L memory socket for a maximum total memory of 8GB DDR3L

INSTALLATIONS IB897 User’s Manual 7 Setting the Jumpers Jumpers are used on IB897 to select various settings and features

INSTALLATIONS 8 IB897 User’s Manual Jumper Locations on IB897 Jumpers on IB897 ...

INSTALLATIONS IB897 User’s Manual 9 JP2: LVDS Panel Brightness Control Selection JP2 Brightness Control (PWM mode) Open 3

INSTALLATIONS 10 IB897 User’s Manual JP5: Clear ME Contents JP5 Setting Function Pin 1-2 Short/Closed Normal Pin 2-3 Short/Closed Clear ME REG

INSTALLATIONS IB897 User’s Manual 11 Connectors on IB897 Connector Locations on IB897 ...

INSTALLATIONS 12 IB897 User’s Manual Connector Locations on IB897 Bottom side

INSTALLATIONS IB897 User’s Manual 13 CN3: USB3.0 Connector CN4, CN5: Gigabit LAN CN4: Intel® I210IT CN5: Intel® I210

INSTALLATIONS 14 IB897 User’s Manual LED1: Power LED and HDD LED The green LED at the bottom is power LED. The red LED on top is the HDD LED. CN1:

INSTALLATIONS IB897 User’s Manual 15 J1: Audio Connector (DF11-12DP-2DSA) Signal Name Pin # Pin # Signal Name LINEOUT_R 2

ii IB897 User’s Manual Acknowledgments AMI BIOS is a trademark of American Megatrends Inc. PS/2 is a trademark of International Business Machines

INSTALLATIONS 16 IB897 User’s Manual J3: DDR3L SO-DIMM(CH-B) Sockets J4, J6: LVDS Connectors, Hirose DF20G-20DP-1V J4: First Channel LVDS

INSTALLATIONS IB897 User’s Manual 17 J7: DDR3L SO-DIMM(CH-A) Sockets J9: MCU Flash Connector (factory use only) J10: SA

INSTALLATIONS 18 IB897 User’s Manual J11: Smart Battery Pin # Signal Name 1 RST# 2 ICHSWI# 3 Ground 4 SMB_DATA 5 SMB_CLK J12: Mini PCIE Connector

INSTALLATIONS IB897 User’s Manual 19 J14: USB 2.0 Connector Signal Name Pin # Pin # Signal Name Vcc 1 2 Ground D0- 3 4 D1

INSTALLATIONS 20 IB897 User’s Manual J16: VGA Connector (DF11-16DP-2DSA) Signal Name Pin # Pin # Signal Name +5V 2 1 Red Ground 4 3 Green N.C 6 5 B

INSTALLATIONS IB897 User’s Manual 21 J18: Board Input Power Connector Pin # Signal Name 1 +9V to +30V 2 GND J19: Rese

INSTALLATIONS 22 IB897 User’s Manual JP4: SPI Flash Connector (factory use only) JP7: Factory use only JP8: Debug 80 Port Connector (factory use

BIOS SETUP IB897 User’s Manual 23 BIOS Setup This chapter describes the different settings available in the AMI BIOS that

BIOS SETUP 24 IB897 User’s Manual BIOS Introduction The BIOS (Basic Input/Output System) installed in your computer system’s ROM supports

BIOS SETUP IB897 User’s Manual 25 Main Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Main

IB897 User’s Manual iii Table of Contents Introduction ... 1 Pro

BIOS SETUP 26 IB897 User’s Manual Advanced Settings This section allows you to configure and improve your system and allows you to set up some system

BIOS SETUP IB897 User’s Manual 27 LVDS Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. M

BIOS SETUP 28 IB897 User’s Manual Super IO Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Main Advanced C

BIOS SETUP IB897 User’s Manual 29 H/W Monitor Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Main

BIOS SETUP 30 IB897 User’s Manual CPU Configuration This section shows the CPU configuration parameters. Aptio Setup Utility – Copyright © 2013 Ame

BIOS SETUP IB897 User’s Manual 31 CPU PPM Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc.

BIOS SETUP 32 IB897 User’s Manual IDE Configuration SATA Devices Configuration. Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc.

BIOS SETUP IB897 User’s Manual 33 SDIO Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. M

BIOS SETUP 34 IB897 User’s Manual Chipset Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Main Advanced Chipset

BIOS SETUP IB897 User’s Manual 35 Security Settings This section allows you to configure and improve your system and allows

iv IB897 User’s Manual This page is intentionally left blank.

BIOS SETUP 36 IB897 User’s Manual Boot Settings This section allows you to configure the boot settings. Aptio Setup Utility – Copyright © 2013 Amer

BIOS SETUP IB897 User’s Manual 37 REMARKS: Before the installation of Windows 8, go to the BIOS Setup to check that the Boo

BIOS SETUP 38 IB897 User’s Manual Save & Exit Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Main Advanced

DRIVERS INSTALLATION IB897 User’s Manual 39 Drivers Installation This section describes the installation procedures for so

DRIVER INSTALLATION 40 IB897 User’s Manual Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before th

DRIVERS INSTALLATION IB897 User’s Manual 41 VGA Drivers Installation 1. Insert the DVD that comes with the board. Click I

DRIVER INSTALLATION 42 IB897 User’s Manual Realtek High Definition Audio Driver Installation 1. Insert the DVD that comes with the board. C

DRIVERS INSTALLATION IB897 User’s Manual 43 Intel Trusted Execution Engine Installation 1. Insert the DVD that comes

DRIVER INSTALLATION 44 IB897 User’s Manual Intel Sideband Fabric Device Driver Installation 1. Insert the DVD that comes with the board. Cl

DRIVERS INSTALLATION IB897 User’s Manual 45 GPIO Controller Driver Installation 1. The driver for the GPIO controllers

INTRODUCTION IB897 User’s Manual 1 Introduction Product Description IB897 is a 3.5-inch single board computer based on the

DRIVER INSTALLATION 46 IB897 User’s Manual 4. When the driver software in the location has been found, click Next to proceed with the installation.

DRIVERS INSTALLATION IB897 User’s Manual 47 Notes on Boot Option and Windows 8 Setup 1. Before installing Windows 8, chec

APPENDIX 48 IB897 User’s Manual Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port add

APPENDIX IB897 User’s Manual 49 B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify

APPENDIX 50 IB897 User’s Manual C. Digital I/O Sample Code File of the NCT5523D.H //----------------------------------------------------------------

APPENDIX IB897 User’s Manual 51 File of the MAIN.CPP //--------------------------------------------------------------------

APPENDIX 52 IB897 User’s Manual void Dio5Initial(void) { unsigned char ucBuf; ucBuf = Get_NCT5523D_Reg(0x1C); ucBuf &= ~0x02; Set_

APPENDIX IB897 User’s Manual 53 File of the NCT5523D.CPP //---------------------------------------------------------------

APPENDIX 54 IB897 User’s Manual void Set_NCT5523D_LD( unsigned char LD) { Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, NCT5523D_REG_LD); ou

APPENDIX IB897 User’s Manual 55 D. Watchdog Timer Configuration The WDT is used to generate a variety of output signals af

INTRODUCTION 2 IB897 User’s Manual Specifications Product Name IB897 [default silk screen model # on PCB is IB897] Form Factor 3.5” disk size SBC

APPENDIX 56 IB897 User’s Manual File of the MAIN.CPP. //--------------------------------------------------------------------------- //

APPENDIX IB897 User’s Manual 57 void WDTEnable(unsigned char NewInterval) { unsigned char bBuf; Set_NCT5523D_LD(0x08);

APPENDIX 58 IB897 User’s Manual File of the NCT5523D.CPP //--------------------------------------------------------------------------- // // THIS COD

APPENDIX IB897 User’s Manual 59 void Set_NCT5523D_LD( unsigned char LD) { Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PO

60 IB897 User’s Manual

INTRODUCTION IB897 User’s Manual 3 Checklist Your IB897 package should include the items listed below.  The IB897

INTRODUCTION 4 IB897 User’s Manual Board Dimensions

INSTALLATIONS IB897 User’s Manual 5 Installations This section provides information on how to use the jumpers and connectors